Precautions for CE Markings Keyence confirms that the LS Series . LS- Photoelectric Sensor or Proximity Sensor Timing input signals are sent. Find great deals for 1 PC KEYENCE Ls CCD Laser Micrometer. Shop with confidence on eBay!. LS High-performance controller. Visible measurement pointController with Target Viewer. High-durability CCD . The LS Series measures the outer diameter of a fiber continuously and .. E-mail: [email protected]
|Published (Last):||13 March 2004|
|PDF File Size:||12.53 Mb|
|ePub File Size:||7.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
1 PC KEYENCE Ls-7601 CCD Laser Micrometer
Changes the minimum display unit of measured values. Setting Range Two-point calibration requires two types of master workpieces that are different to each other in size. Page 96 Chapter 5 Function Settings Application Example of Measuring modes Select the measurement mode according to the type of target and measuring condition.
All function keys other than the display selection function key are locked. Don’t see what you’re looking for? The following format will be used for the corresponding measured value.
Target Viewer Function on page Tolerance display Displays the preset tolerance values. Page 46 Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Eccentricity In the following example, the outer diameter and eccentricity of the roller is measured while the roller moves. Page Chapter 10 Troubleshooting Error Messages The following section explains error messages that will be displayed if the LS Series has errors while in operation.
LS – Controller, with Monitor Function | LS series | KEYENCE UK & Ireland
Page 42 Chapter 3 Easy Keydnce Guide Measurement of Outer Diameter and Width with Single Measuring Head In the following example, a single measuring head is used to measure the outer diameter of an object in one direction. The LCD monitor is factory-adjusted. Chapter 8 RSC Communication using an External Synchronous Trigger The following section provides information on how to obtain output from the RSC interface in kryence with a timing input into the input terminal.
Tell us about it.
LS – Controller, with Monitor Function | LS series | KEYENCE America
Command Output number 0: Area Selection Area When a target is located in the measuring area as shown below, the light into the receiver is partly obstructed, thus creating a shadow. OUT1 Repeat steps 7 and 8 until all the digits are input.
Chapter 1 Getting Started 3 Connect the cable between the controller and measuring head. Page 49 Chapter 3 Easy Setting Guide Group Processing In the following example, the average, maximum, or minimum value is calculated as ks-7601 from the measuring data on the group of targets. Share Facebook Twitter Pinterest.
Set the key lock type to ALL: Page Chapter 5 Function Settings 08 09 10 Note: Chapter 3 Easy Setting Guide Measurement of Outer Diameter and Width with Single Measuring Head In the following example, a single measuring head is used to measure the outer diameter of an object in one direction. There was a problem completing your request. This section provides information on the overview of program settings and setting methods. Page Chapter 10 Troubleshooting Problem Inspection Remedy Check that the cover glass of the transmitter Remove the dirt and dust from the or receiver is free of dust and dirt.
This range varies with the display unit or minimum display unit setting. Then the LS Series will start sampling after a certain time period i. Appendix Environment Setting Record Sheet Use the following tables to record your environment setting details. Otherwise, the camera and connected devices may be damaged. These commands allow the following operations. Page Appendix R Reference value mode Page 8 Optimum Measurement Methods Refer to the following methods, and select the optimum measurement method according to the type of target.
Page Chapter 5 Function Settings Note: The following measurement modes can be used for group processing. There’s a problem loading this menu right now. Environment Setting Record Sheet The result of measurement is displayed as OUT1.
KEYENCE LS-7600 User Manual
Chapter 1 Getting Started Use the 5-mm-deep M4 bottom mounting holes of the transmitter and receiver as shown in the illustration. Page 63 Chapter 5 Function Settings The LS Series is available to the measurement of a variety of items by making setting changes.
Area Settings Area settings include the following items. Automatically set to a fixed value. When repeating the two-point calibration, the previous settings will appear on the screen, which will be different from those in the above setting example. See more product details. Control Panel Functions and Nomenclature Be the first to review this item Product Warranty: