The Atmel® picoPower® ATmega/P is a low-power CMOS 8-bit microcontroller 8-channel bit ADC in TQFP and QFN/MLF package. •. Temperature. Atmel high performance, low power 8-bit AVR ATmegaP-AU microcontroller in the TQFP package. Okay, so I’m about to blow up. I’ve tried to use perhaps 10 Atmega TQFP without any success.

Author: Kajidal Volkree
Country: Andorra
Language: English (Spanish)
Genre: Relationship
Published (Last): 2 June 2016
Pages: 452
PDF File Size: 19.59 Mb
ePub File Size: 10.42 Mb
ISBN: 798-3-71302-217-9
Downloads: 83070
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigis

ATmega328P Microcontroller – TQFP

Clearly Qtmega328 doing something incorrectly, and I wouldn’t doubt if it was because it’s not as simple as hooking the AVR programmer directly up to the chip to program it.

If all that is correct, there are a couple other things that could cause that error: I’ve simply connected the AVR programmer to the chip in the adapter socket as follows AVR connector on left, chip on right. If all that is correct, there are a couple other things that could cause that error:. Using SCK period of 10 usec avrdude: Block Poll Page Atmeg3a28 Memory Type Mode Delay Size Indx Paged Size Size Pages MinW MaxW ReadBack eeprom 65 20 4 0 no 4 0 0xff 0xff flash 65 6 0 yes 0xff 0xff lfuse 0 0 0 0 no 1 0 0 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 0x00 0x00 efuse 0 0 0 0 no 1 0 0 0x00 0x00 lock 0 0 0 0 no 1 0 0 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type: Reset is driven by the programmer, and besides has an internal pullup.


When programming through SPI, the chip accepts the program even if the fuses are set to accept clock signal from external clock.

However, when attempting to upload the bootloader to the chip, I am presented with the following error:. The AVR programmer will not supply power. ATmegaP Chip Erase delay: This question does not appear to be about electronics design within the scope defined in the help center.

ATMega328 – TQFP

The reset pin lacks the normal ESD protection, and so is fairly easy to fry. TomCarpenter, the programmer does provide power. Crystal requirement comes when booting through the bootloader i.

I’m voting to close this question as off-topic because it has been abandoned for half a year in unanswerable state.

Well first of all, check the wiring. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Check that the ISP header connects to the pins that it ought to, and check that you have the chip oriented correctly in the socket The USBtiny has a switch to power the target, so make sure that’s in the correct position.


Ground yourself and use an ESD mat. ISP requires a working clock source. Assuming your connection is incorrect, first you need to add a pull-up resistor to the reset pin; 1kk should be alright.

If the reset pin has been disabled, you’ll need a special high voltage 12V programmer to recover it. That is pretty tqp all you need.

ATmega – Wikipedia

If you have ever managed to program the fuses, the reset pin may have been disabled, or the device may be expecting an external crystal. Atmega 2 9 SCK serial program mode: Error while burning bootloader. It looks like the log text says ‘programmer operation not supported’, could be a symptom of tqdp cmd line args.

Only HV programming does not. Any help would be appreciated. Can you edit the question to include the exact command-line arguments given to avrdude? If this question can be reworded to fit the rules in the help centerplease edit the question. It’s tfp checking its in the correct position, though.

Have you applied power to the circuit? Home Questions Tags Users Unanswered.